Note: in case you are utilizing a photocopy, put the blue filter behind the master and insert them collectively.put a blank card on the foam bed (to maintain your artwork from sticking to it), industrial filter mesh and put your original artwork on high of that. i drew this image using the gocco marker (included in gocco set). place your artwork where you want it.
shut the lid can verify visually that your artwork is where you need it to be.
however 2 bulbs into the print hood (yellow part) can insert the hood into the print gocco physique. here’s the primary facet.
here’s the second side.
at this point the order is high to bottom: yellow flash hood; clear plastic window within the gocco; blue filter; mesh master; unique artwork; blank paper; foam bed.
when it’s pressed down, the hood makes an entire circuit that may trigger the bulbs to flash.
put each your hands on the front of the gocco (the picture just has one in every of my arms, because the other one is holding the digital camera, however you may see the place your arms ought to go).
push down (you will note the the flash and hear a crackling noise) and hold for 3-5 seconds.
open your gocco. If you’re ready to read more information about industrial filter mesh price look into our own web-site. your artwork will most like be stuck to the master. remove the master (and blue filter, if you used it to create a master from a photocopy).
if you remove the yellow print hood, watch out to not touch the bulbs until they cool.
here is the grasp with my design uncovered on it.
with the master out of the gocco, screen aspect down and sitting on a piece of scrap paper, raise the clear plastic up and squeeze ink out of the tube on to the realm the place your design is. if you haven’t but, peal your unique off the master. (leaving it on till now could be useful to see the place exactly you should ink).
change the clear plastic layer and and put the inked master back into the gocco the identical manner and place as earlier than. if you haven’t removed the flash hood, do it now.
now the order is: clear plastic window within the gocco, clear plastic sheet over the ink, ink, mesh master.
put whatever you want to print on on the sticky gray foam bed. now it will likely be helpful that it’s sticky because it holds your prints in place.
close the gocco to make a print. *repeat.*
that is my print on fabric.
these are all the things i printed on. and printing on felt was superior.
this system above can be used to print on paper or fabric, although to print on fabric, it’s essential to used special gocco fabric ink. (EDIT: you may print on fabric with the identical kind of display and same process that you should use to print on paper-just use ‘gocco stamp ink for fabric’).
one other approach to print on fabric is as a substitute of utilizing the hello mesh master (which can be utilized for both paper or fabric printing), use the gocco display screen masters especially for screen printing mesh printing on fabric. with these, you can’t use the gocco to print, relatively you use the gocco to make the screen, and then print like typical screenprinting, industrial filter mesh utilizing gocco screenprinting ink, which comes in jars and is not the same because the ‘stamp ink for fabric’ that comes in tubes.
it is a screened print i did using the gocco display and screen inks. it was from a photocopy of a conventional japanese display screen, so the meshy background is from the original picture.
cleanup:
the screens can be re-used many many many times. you can store them in a ziploc bag in the fridge and take them out when you find yourself prepared to make use of them subsequent time. this fashion, you do not even have to clean off the inks.
the fabric inks are water primarily based. i recommend taping the cardboard edges of your screen earlier than you start, that manner they won’t fall apart or warp after cleanup with water.
you should utilize the gocco cleaner with the paper inks, however they may even wash off if held underneath working water (that is the place the tape comes it). you can too wipe with a sponge or paper towels. remember the fact that it’s vital to clean the print area solely, and it the display screen is stained in different places it will not have an effect on your future prints.
current situation:a number of years ago gocco’ s mother or father firm riso announced that gocco’s would now not be exported to the united states. this triggered a bit of a frenzy and lead to creation of the save gocco marketing campaign. EDIT: after several years of restricted supplies, it appears that evidently gocco will certainly be ceasing production in the following yr or so.
